青花漫舞6305467
蒙娜丽莎瓷砖温馨提示 该步骤应注意:
橱柜中往往会安装一些嵌入式电器，比如:消毒柜、烤箱、洗碗机等等，一般人会把电器的电源就留在嵌入的这个柜体的后面，安装时直接插上，以后就只能靠电器前面的开关来控制了。
其实最好还是把电源插座留到和此嵌入电器相邻的柜体里面，在两个柜体间的隔板上打个洞，把电源线穿过去，这样以后的使用会方便很多，而且电源也不用老插着。
另外，象烤箱这样的发热量大的电器，在安装时，最好在所在柜体的内部板上垫上石棉等隔热材料，而且此柜体一定要留好散热的地方，如果是安装在岛台上，那么此柜体的背面最好做成可以打开的，这样在使用时，可以把整个背面打开散热。
1、灶具最好不要设计到最靠墙的那组橱柜上，使用上会有很多不便，灶具和水槽之间一定要留有距离，因为这两处都是容易放重东西的地方，靠太近，日后台面很容易变形，而且中间有台面，清洗过的原材料也好放置其上，炒菜的时候方便取用。
2、給微波炉等电器留孔位的时候，不要和现在用的尺寸严丝合缝，万一以后需要更新换代，可能会放不进去。
3、最边上的一组橱柜，一定要考虑开门方向和拉手的安装，很多时候安装完毕后拉手都会打到墙或其它柜
子，不但使现在的柜子无法完全打开门，而且长期磕碰也容易损伤。
橱柜安装注意事项
橱柜安装注意事项
Cabinet installation notes.Txt52 everyone is a parabola, talent determines its opening, and the highest point will require the efforts of the day after tomorrow. No autumn leaves fall, where spring green shoots hungry bright? Only know how to lose, will have again. Cabinet installation:
The first shop in order to avoid bumps broken tiles blanket before installation
After installation, return the original order to the staff and ask for the after-sale warranty card
The installation generally requires two installation master, after entering the cabinet will be in accordance with the cabinet table - - - - the cabinet basin - range - leading electrical installation order.
Cabinet installation: before installing the cabinet, the workers should sweep the floor of the kitchen so as to measure the ground level accurately. If the cabinet and the ground can not reach the level of the installation slot, cabinet doors can not balance, installation workers use level on the ground, the wall was measured after the ground level will be able to understand the situation, the final adjustment of the cabinet level.
If the cabinet is L type or U type, need to find a reference point, L type cabinet extending to both sides from the right angle, if from both sides to the middle. There may be gaps, U type cabinet is the first in the middle of a cabinet stacked
neatly, and then from two at right angles to both sides to avoid the gap. The cabinet placed after the need for leveling cabinets, cabinet level adjustment by adjusting the leg of the cabinet.
The connection between the cabinets is also an important step in the installation of the cabinet. 4 connecting pieces need to be connected between the cabinet bodies to ensure the tightness between the cabinets. Some cabinet manufacturers in order to save installation costs, the use of poor quality self tapping screws to connect. Self tapping nails not only affect the appearance of the cabinet, and can only be locked from one end of the cabinet, the connection is not high.
Cabinet installation: cabinet after installation can be installed in the upper cabinets, installing a countertop, in order to ensure the expansion bolt level, need to draw the horizontal line on the wall, generally horizontal lines and the surface distance is 650 mm in height, consumers can according to their own situation, the distance adjustment between the cabinet and the cabinet to the workers, to facilitate the use of the day after.
When installing a countertop also needs to be connected by the connectors to ensure the connection of the cabinet body. The cabinet is installed, we must adjust the cabinet level, the appearance of the cabinet level and not directly affect the cabinet.
Table installation: because the kitchen decoration, will lead to the original cabinet plan size error, in order to reduce the error, some cabinet manufacturers in the cabinet and the
cabinet after the installation of a period of time and then install the table, so that the error table cabinet and the wall cupboard after installation can be adjusted to ensure the cabinet designers, installation data the accurate.
According to reports, the current consumer use of the majority of artificial stone countertops or natural stone countertops, stone countertops are a few pieces of stone bonding, adhesive bonding time, and grinding degree will affect the appearance of the table. In general, the summer bonding table needs half an hour, and the winter takes 1 hours to 1.5 hours. When bonding, you should use professional glue for bonding. In order to ensure the beauty of the table joints, the installation workers should use grinding machines to polish and polish.
Hardware installation: basin, faucet, pull basket is also the highlight of the cabinet.
In the installation of condole ark and table, in order to avoid falling into the basket for wood track application covering covering basket, so as not to affect the day after use.
Basin installation involves water problems. The installation of cabinets, water installation will be the scene opening way, use a punch professional according to the size of pipe drilling, drilling pipe diameter should be at least more than 3-4 mm, and will the opening part is sealed with a sealing strip perforating, prevent wood edge water swelling deformation, affect the service life of the cabinet.
In order to prevent water seepage in the basin or the water,
the connection between the hose and the basin should be sealed or sealed with glass glue, and the hose and sewer should be sealed with glass glue. Because the water pipe is at the bottom of the cabinet, consumers can not be tested, some installation workers in order to save costs do not use glass glue sealing, resulting in the days after the sewer odor or Water Leakage.
If the cabinet leaks, there may be three reasons: one is the leakage between the basin and hose, the other two is the leakage between the pipe and the water, and the other is the quality of the pipeline itself.
Kitchen electrical installation: embedded electrical cabinet in the installation site only need to open the power supply hole, but the hole can not open too small, so the later maintenance is not convenient disassembly. Some consumers because of the water meter and gas meter unsightly require workers to pack up, experts said that if the workers will wrap up the water meter and gas meter, after the repair will be trouble, countries also have the relevant standards do not allow packaging meter and gas meter.
When installing lampblack exhauster, in order to ensure the use and smoking effect, the distance between the range hood and the stove is usually between 750-800 millimeters. If the installation height is too high, the smoking effect will be affected. When cooking fume exhauster, align with the cooker, adjust the height according to the actual situation.
Install the cooker is the most important connection source, make sure the air mouth does not leak, gas should have natural
gas company sent a connection, if the decoration workers to install, also need to make natural gas company to detect leakage.
Adjust the door: the last step is to adjust the installation of the cabinet door, ensure the door gap is uniform and flat vertical cabinet depth is 550 mm, the cabinet is 300 mm, consumers can also be adjusted according to the actual situation. After adjusting the cabinet door, the workers should also clean the garbage left when installing the cabinet, and ensure the cleanliness of the owner's kitchen.
1, matters needing attention
1) cabinets, wall back on-site production should pay attention to with wood strength file anyway;
2) when installing lampblack exhauster, the shutter on the drain can not be thrown away by the construction personnel, and the construction personnel shall be urged to install it according to the instruction manual;
3) in addition to the correct use of adhesives, the cabinet should be connected with hardware as far as possible;
4) kitchen cabinets and cabinets must be fireproof or painted with fire retardant paint;
5) kitchen wall, hanging kitchen, cupboard door, door sheet welt, to use, to avoid dropping contraction;
6) the material used in the bottom of the drawer is thicker than the others.
2, acceptance standards
1) the installation of door panels shall be in correspondence with each other, and the width of all the joints shall be the same;
2) the handle should be on the same horizontal line;
3) the surface should be smooth and bright, without obvious scratches;
4) the upper and lower water connections are unobstructed;
5) drawer 20mm or so, can automatically shut, indicating that the bearing capacity is stronger
橱柜安装注意事项
www.moguzx.com
随着家庭生活的不断提升，很多家庭对壁柜的要求越来越高。壁柜不仅可以给而我们的生活带来便利而且还能起到美观的作用。那么我们在进行橱柜安装的时候需要进行哪些事项呢？
对于选用材料，收纳设计，安装常识您又了解多少?您不妨先试着回答以下八大问题：
01自己的厨房布局属于哪一种?
了解厨房布局有利于设计安装橱柜时作出合理规划，您的厨房是适合安装l型橱柜?u字形橱柜?还是一字形橱柜?了解清楚布局，方便您与设计师的沟通。 02厨房分为哪几个区域?
厨房大致可分为储藏区、洗涤区、备餐区、烹饪区。各区域分别合理规划，使用起来更舒心。
03怎样设计不规则的厨房?
厨房空间较大，可以选择把餐桌放进厨房。
04橱柜的台面污渍难以擦拭?
橱柜台面选择要谨慎，好的台面结构致密，抗污防渗，省下不少清洁的麻烦。 05柜门关合会不会发出砰砰的噪音?
开合顺畅，体验厨房宁静，静音阻尼铰链是您不错的选择。
06打开吊柜的门时会不会碰到头？
吊柜门的设计有很多种，通常不会碰到头，如果业主身高较高，可以调整一下吊柜安装的高度。
07地柜太深，取出厨具会不会不方便?
对于比较深的柜体，可以安装小怪物拉篮和飞碟拉篮，可以方便取出厨具。 08厨房陆续增加厨具，会不会不够地方收纳?
不妨在厨房安装高身拉篮，收纳空间将会大大增加。
橱柜安装注意事项
原文地址:新居网家具频道http://news.homekoo.com/chugui/743
橱柜安装注意事项
橱柜是我们厨房主要装饰品，一款好的橱柜价值不菲，橱柜不仅要看好柜体材质与五金配件，也要注重橱柜的安装，今天就为大家说说橱柜安装注事项。
1、壁柜的测量。壁柜的柜体既可以是墙体，也可以是夹层，这样既保证有效利用空间，又不变形，但一定要做到顶部与底部水平、两侧垂直，如有误差，则要求洞口左右两侧高度差小于5mm，壁柜门的底轮可以通过调试系统弥补误差。
2、地柜安装:安装地柜前，工人应该对厨房地面进行清扫，以便准确测量地面水平。安装时如果橱柜与地面不能达到水平，橱柜柜门的缝隙就无法平衡，安装工人使用水平尺对地面、墙面进行测量后就能了解地面水平情况，最后调整橱柜水平。
3、吊柜安装:地柜安装完毕后则可以进行吊柜安装，安装吊柜时，为了保证膨胀螺栓的水平，需要在墙面画出水平线，一般情况下水平线与台面的距离为650毫米，消费者可以根据自身身高的情况，向工长提出地柜与吊柜之间距离的调整，以方便日后使用。
4、橱柜台面安装:台面安装好后，一定要水平。人造石的优点之一就是无缝拼接，如果你能清楚得看到胶水线，接缝肯定没做好，不用理会安装工人说出了多少个理由。
5、五金安装:水盆、龙头、拉篮也是橱柜
文章来自新居网
橱柜安装注意事项
准备作要工好做
??、1厨最好约电送齐货、安装。需嵌入要安装式的烟机灶具、、消毒这几大件，柜橱柜开始安装在时的，业候要主前提定约厨送货电、装的时间安最好，一并也场。进许橱柜设也师会告诉你，只需计商去场想买把的家电尺寸下抄，做橱柜时来会预留好置位以，买来后接直放入可就啦以。专家建议还但是在安橱装的柜候一并时装安位到首先，家电。更很快新，可能当量时尺寸的好电器等，装完修再未必还去货有，而经预留的空已是无位法再整调；的次其，电和橱厨柜起安一，装橱柜装安工按整体会果进效调行整，保最佳的一体化证果。
效??2业、事主先将要厨房地面边和角边角仔细打一扫遍等。柜橱装完后安，很多落就角也打扫不到了，再虽安然前工人装师也会傅打扫，但不总如业主自打扫己的细。致
?
柜?体如验何
收??3、平
度整。柜地要没安在台装之面晃前晃一是否牢看固，装好安，后要水用平测量一尺排地柜否是是平。水
??4、封。边优质橱柜封边的腻、细光滑手、感好，线平封直接，精细。大品牌用封头机边次完一成边、封头断修边、倒角、、抛光工等序，胶涂均，压贴封边匀的力压稳定，保最证确精尺的寸而作。坊式厂小是人工涂则、压贴胶封边、、抛光，由压力于不均匀，很地方多封不牢固边，会还造成板内材的害气有挥体发到气空中
??。5、水防箔铝装有。水的柜体底槽板要有贴整张防水铝箔，且三的边上翻1cm要防，止水槽或道管的冷凝水侵蚀体柜。
门板何如验收
??
、颜6。色查检门颜板和色材质否与订是的一购致门板与订色，存卡在少许差是色常正，的是但好做的板整门颜色不体允有色差。
许
??7正、面。反逐块检门查的板正表反有无面变、形伤划、泡等起现象。
?8?门缝、。缝门应下一上，宽致度均，匀门宽缝度1在-m2间。m
?台?如面何验收
?
?9平整、。度面台安好装后一要定再次用平尺检查平水整。度
??10
接、。缝果如面装好台能清楚后看的到接缝的水线，胶或用是手感觉能到明的错缝显，说明缝接定没做好。肯
??11、差。同一型色号颜的人造色石由于出厂，间时不会同存在定一度的色差现程象，消费者在台面进场一定时要注对比意看。查
??12
、开。台孔面上槽水灶具和的位置都需开要，开孔孔边要圆缘滑，能有锯齿不状；形个角四做要定的一弧度不，能简是单直的，角而且特要加固别。
?13、后档?水为。了防台面止水流到的橱柜后面所以，台，面靠的地墙，一方上翻定形挡水成需。注要意是，这个上翻的定一要有平滑弧度是上翻的，而能不是角的上翻，直否则留下难以清会理
的死。角
??14打胶、。后水档墙与连面的地接会方打上色玻璃白胶台面与水槽连接的；方地打上透明的玻会璃。胶打胶前业主定一要查看玻璃胶包装是否标外注防霉功能，打有胶一后定督要工促把多人的胶及时余理清。
掉金五如验收
何?
?1、组5孔眼。装要一块看上的孔位板不是是隔间均、不能匀错位有。位的孔配和精度会合影橱响柜箱的结构体固牢性专。大业用多厂钻排次完成一块板板一边板面、的上干孔。若而小牌品则现场手工打是孔
??。61抽、滑屉。轨要注意需查检屉和拉抽式出篮、架安装是否固稳顺畅抽，屉隙缝是均否，匀应做到畅、无顺、声巧轻软、回。弹
??17、铰链铰链。是橱柜里要的五重件金质，好的铰量链厚、柔韧性、钢腐蚀性抗，好底座高力、臂、长随定意位位无移，使在用开时合自如、无噪。音查检手是拉水否平是，摇否，门晃板关时应开互相无撞。碰
?
施工?务服要到位
??18、成品保护
橱柜。场时进般都一是修末期了，安装装时工人当对应房厨设的如备气表和装修成燃品如瓷等砖行进效保护有。
?
19、?清施扫现场工打。台面和磨柜体打孔时产生会大量粉和尘末锯，装完安，除了清后理面地和柜上橱粉的外，尘还清理柜体内的要尘，粉最清理后现，收场包集装及施物工留后的下圾，垃一带走。并
