范文一:旋转编码器接线图
旋转编码器接线图 以下为编码器接线图介绍,与plc连接,以欧姆龙CPM1A为例:1.NPN集电极开路输出接线方式如下图所示:
此接线方式应用于当传感器的工作电压与PLC的输入电压不同时,取编码器晶体管部分,另外串入电源,以无电压形式接入PLC。但是需要注意的是,外接电源的电压必须在DC30V以下,开关容量每相35mA以下,超过这个工作电压,则编码器内部可能会发生损坏。接线方式描述:编码器的褐线接编码器工作电压正极,蓝线接编码器工作电压负极,输出线依次接入PLC的输入点,蓝线接外接电源负极,外接电源正极接入PLC的输入com端。2.电压输出接线方式如下图所示:
接线方式描述:编码器的褐线接电源正极,输出线依次接入PLC的输入点,蓝线接电源负极,再从电源正极端拉根线接入PLC输入com端。3.PNP集电极开路输出接线方式如下图所示:
接线方式描述:编码器的褐线接工作电压正极,蓝线接工作电压负极,输出线依次接入PLC的输入com端,再从电源负极端拉根线接入PLC的输入com端。4.线性驱动输出接线方式描述:输出线依次接入后续设备相应的输入点,褐线
接工作电压的正极,蓝线接工作电压的负极。以下为旋转编码器接线图介绍,与计数器连接,以H7CX(OMRON制)为例H7CX输入信号分为无电压输入和电压输入。1.无电压输入以无电压方式输入时,只接受NPN输出信号。(1)NPN集电极开路输出的编码器接线方式如下图所示:
接线方式描述:褐线接电源正极,蓝线接电源负极,再从电源负极端拉根线接6号端子,黑线和白线接入8和9号端子,如果需要自动复位,则橙线接入7号端子。(2)NPN电压输出的编码器接线方式如下图所示:
接线方式与NPN集电极开路输出方式一样。2.电压输入(1)NPN集电极开路输出的编码器接线方式如下图所示:
接线方式描述:褐线接电源正极,蓝线接电源负极,再从电源负极端拉根线接6号端子,黑线和白线接入8和9号端子,如果需要自动复位,则橙线接入7号端子。(2)PNP集电极开路输出的编码器接线方式如下图所示:
范文二:旋转式编码器接线图
?与PLC连接,以CPM1A为例
?NPN集电极开路输出
方法1:如下图所示
这种接线方式应用于当传感器的工作电压与PLC的输入电压不同时,取编码器晶体管部分,另外串入电源,以无电压形式接入PLC。但是需要注意的是,外接电源的电压必须在DC30V以下,开关容量每相35mA以下,超过这个工作电压,则编码器内部可能会发生损坏。
具体接线方式如下:编码器的褐线接编码器工作电压正极,蓝线接编码器工作电压负极,输出线依次接入PLC的输入点,蓝线接外接电源负极,外接电源正极接入PLC的输入com端。
方法2:编码器的褐线接电源正极,输出线依次接入PLC的输入点,蓝线接电源负极,再从电源正极端拉根线接入PLC输入com端。
?电压输出
接线方式如图所示:
具体接线方式如下:编码器的褐线接电源正极,输出线依次接入PLC
的输入点,蓝线接电源负极,再从电源正极端拉根线接入PLC输入com端。
不过需要注意的是,不能以下图方式接线。
?PNP集电极开路输出
接线方式如下图所示:
具体接线方式如下:编码器的褐线接工作电压正极,蓝线接工作电压负极,输出线依次接入PLC的输入
com端,再从电源负极端拉根线接入PLC的输入com端。
?线性驱动输出
具体接线如下:输出线依次接入后续设备相应的输入点,褐线接工作电压的正极,蓝线接工作电压的负
极。
?与计数器连接,以H7CX(OMRON制)为例
H7CX输入信号分为无电压输入和电压输入。
?无电压输入:
以无电压方式输入时,只接受NPN输出信号。
NPN集电极开路输出的接线方式如下:
具体接线方式如下:褐线接电源正极,蓝线接电源负极,再从电源负极端拉根线接6号端子,黑线和白线
接入8和9号端子,如果需要自动复位,则橙线接入7号端子。
NPN电压输出的接线方式如下:
接线方式与NPN集电极开路输出方式一样。
? 电压输入
NPN集电极开路输出的接线方式如下图所示:
具体接线方式如下:褐线接电源正极,蓝线接电源负极,再从电源负极端拉根线接6号端子,黑线和白线接入8和9号端子,如果需要自动复位,则橙线接入7号端子。
PNP集电极开路输出的接线方式如下图所示:
范文三:编码器接线图
1、海德汉ERN1387正余弦增量型编码器与西威SIEI变频器的接线图:
配编码器
接口
1387信号信号线颜色线颜色白色白/绿色棕色棕/绿色信号信号绿色绿/黑色15针型插信号信号黄/绿色黄/黑色信号信号蓝色蓝/黑色头信号信号橙色红/黑色信号信号红色红色信号信号黑色黑色信号信号灰色灰色信号信号粉色粉色信号信号黄色黄色信号信号紫色紫色
2、海德汉ERN1387正余弦增量型编码器与科比F4变频器的接线图:
配编
码器接口
线颜色线颜色白色白/绿色棕色棕/绿色信号绿色绿/黑色15针型插信号黄/绿色黄/黑色信号蓝色蓝/黑色头信号橙色红/黑色信号红色红色信号黑色黑色信号灰色灰色信号粉色粉色信号黄色黄色信号紫色紫色
3、丹纳赫RF53增量型方波编码器与安川、酷马变频器的接线图:
黑红蓝蓝/黑绿绿/黑紫紫/黑
4、丹纳赫RF53增量型方波编码器与爱默生变频器EV3100接线图:
配编
码器接口
线颜色信号信号线颜色
红色红色棕色棕色 信号 信号黑色黑色15针型插信号信号灰色灰色信号信号蓝色蓝色头信号信号白色白色信号信号蓝/黑色蓝/黑色
信号信号绿色绿色信号信号棕/黑色棕/黑色信号信号绿/黑色绿/黑色信号信号灰/黑色灰/黑色信号信号紫色紫色信号信号白/黑色白/黑色信号信号紫/黑色紫/黑色
范文四:编码器接线图
1、海德汉ERN1387正余弦增量型编码器与西威SIEI 变频器的接线图: 配
接口
线颜色
白/绿色
棕/绿色
绿/黑色
黄/黑色
蓝/黑色
红/黑色
红色
黑色
灰色粉色
黄色
紫色信号信号信号信号信号信号信号信号信号信号信号信号信号信号信号信号信号信号信号信号1387信号信号线颜色白色棕色绿色黄/绿色蓝色橙色红色黑色灰色粉色黄色紫色编码器15针型插头
2、海德汉ERN1387正余弦增量型编码器与科比F4变频器的接线图:
配
码器接口
线颜色
白/绿色
棕/绿色
绿/黑色
黄/黑色
蓝/黑色
红/黑色
红色
黑色
灰色
粉色
黄色
紫色信号信号
信号信号信号信号信号信号信号信号线颜色白色棕色绿色黄/绿色蓝色橙色红色黑色灰色粉色黄色紫色编15针型插头
3、丹纳赫RF53增量型方波编码器与安川、酷马变频器的接线图:
黑
红
蓝
绿
绿/黑
紫/黑
4、丹纳赫RF53增量型方波编码器与爱默生变频器EV3100接线图:
配编
码器接口
线颜色
红色
棕色
黑色
灰色
蓝色
白色
蓝/黑色信号信号信号信号信号信号信号信号 信号 信号信号信号线颜色红色棕色黑色灰色蓝色白色蓝/黑色15针型插头绿色
棕/黑色
绿/黑色
灰/黑色
紫色
白/黑色
紫/黑色信号信号信号信号信号信号信号信号信号信号信号信号绿色棕/黑色绿/黑色灰/黑色紫色白/黑色紫/黑色
范文五:CT 备选件选型 (有编码器接线图)
Commander SK
Options for Commander SK
Michael Nakulski
September 2004
Product Management Copyright 2004 ? Control Techniques
1
Commander SK
INDEX
Page 3 - Options for Commander SK Page 4 - LED Remote Mounting Keypad Page 5 - LCD Remote Mounting Keypad Page 6 - Parameter Memory Stick Page 7 - Fieldbus Option Modules Page 8 - Extended I/O Page 9 - Extended I/O with Real-time-clock Page 10 - Commissioning Software Page 11 - PLC Function Programming Software Page 12 - PLC Function Stick Page 13 - Connecting Cable for PC Page 14 - Additional EMC Filters Page 15 - Top NEMA 1 Cover Page 16 - Bottom Glanding Metal Cover
Product Management Copyright 2004 ? Control Techniques
2
Commander SK
Options for Commander SK
Commander SK has many option possibilities which compliment the standard features and functions making it the most flexible general purpose AC drive. All the options described on the following pages are supported by all three frame sizes of Commander SK. The exception is the SM range of option modules which is only supported by sizes B & C. Size C Size B
Size A
Size 200 to 240V +/-10% 380 to 480 V +/-10%
A 0.25 to 0.75 kW -
B 1.1 to 1.5 kW 0.37 to 1.5 kW
C 2.2 kW 2.2 to 4.0 kW
Product Management Copyright 2004 ? Control Techniques
3
Commander SK
LED Remote Mounting Keypad
Ordering Code: SK-Keypad Remote Description: Remote panel mounting LED keypad display to IP54 (NEMA12) with additional function key. ?Selectable function key with LED to indicate function selected. – Hand-Off-Auto, Jog, Reverse, etc. ?Connects to the RS485 Modbus RTU port on the drive via a standard RJ45 connector ?Connecting cable (up to 30m) ?Simple panel cut-out - 21mm hole ?Fixed keypad on drive remains active.
Compatibility: ? Commander SK only – all sizes
Product Management Copyright 2004 ? Control Techniques
4
Commander SK
LCD Remote Mounting Keypad
Ordering Code: SM-Keypad Plus Description: Remote panel mounting LCD multilingual text keypad display to IP54 (NEMA12) with the additional “Help” key. ?For remote panel mounting only ?Multi-lingual – 3 lines of text (English, French, Spanish, German & Italian) ?Help function key ?Connects to the RS485 Modbus RTU port on the drive via standard RJ45 connector ?Simple panel cut-out - 21mm hole ?Fixed keypad on drive remains active ?A PC software tool enables you to set up your own text lines.
?Exactly the same LCD keypad as used by Unidrive SP
Compatibility: ? Commander SK – all sizes ? Unidrive SP ? Commander SX (IP66)
Product Management Copyright 2004 ? Control Techniques
5
Commander SK
Parameter Memory Stick
Ordering Code: SmartStick Description: Upload drive parameters to the SmartStick for storage or for easy setup of identical drives or for downloading to replacement drives.
?SmartStick - 1 parameter configures as: ?Read - program the drive with contents ?Program - Drive parameter set loaded onto SmartStick ?Boot - Loads parameters at power up (and can then be removed) - Read only and can’t be changed!
Compatibility: ? Commander SK – all sizes
Product Management Copyright 2004 ? Control Techniques
6
Commander SK
Fieldbus Option Modules
Ordering Code: SM-PROFIBUS DP SM-DeviceNet SM-CANopen SM-INTERBUS SM-Ethernet (end 2004) Description: The most popular industrial fieldbus protocols are available in the SM range of option modules. One option slot in sizes B & C allows an SM fieldbus option and other specified SM option modules to be fitted. Use fieldbus firmware version 3.0 or higher for complete compatibility for the entire range of AC drives.
ETHERNET
(TCP/IP)
Compatibility: ? Commander SK sizes B & C ? Unidrive SP ? Commander SX (IP66)
Product Management Copyright 2004 ? Control Techniques
7
Commander SK
Extended I/O
Ordering Code: SM-I/O Lite Description: Additional I/O option with the following connections: ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 0V ±10V bi-polar or 4-20mA Analogue input 0-10V or 4-20mA Analogue output +24V Digital input Digital input This
Commander SK
Extended I/O with Real-time-clock
Ordering Code: SM-I/O Timer Description: Real-time-clock for scheduling drive running as well as the following additional I/O connections: ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 0V ±10V bi-polar or 4-20mA Analogue input 0-10V or 4-20mA Analogue output +24V Digital input This
Commander SK
Commissioning Software
Ordering Code: CTSoft (comes free-of-charge with product CD ROM) Description: Software for your PC or laptop which allows you to commission and store parameter settings. Use with CT Comms Cable. ?Drive Set up & Monitoring Software Tool this one software package handles all key CT drive products ?Upload / download / store parameter setups ?Easy set up Wizards
Compatibility: ? Commander SK – all sizes ? Unidrive SP
Product Management Copyright 2004 ? Control Techniques
10